Emotiva XPA Gen3 amplificateur

Emotiva XPA Gen3 amplificateur a canaux modulaire (2 à 11)

UGS : XPA Gen3 Catégories : , Brand:

Description

Emotiva XPA Gen3

Modular Construction

The XPA Gen3 modular power amplifier is comprised of a heavy-duty chassis, which houses the oversized power supply, and up to seven amplifier modules. The XPA Gen3 can be purchased with anywhere between two and seven amplifier modules installed, and additional amplifier modules may be installed as more channels of amplification are needed (up to a maximum of seven modules). The front panel display and protection system are designed to work with the maximum number of channels, and so need not be updated when the XPA Gen3 is expanded; on the rear panel, slots not occupied by amplifier modules will be covered with protective cover panels.

 

Circuit Topology

A fully modular audio power amplifier with a high-efficiency switch mode power supply (SMPS), independent, fully discrete, dual differential, high current, short signal path Class A/B amplifier modules, Optimized Class H™ power supply topology, and microprocessor-controlled fault protection.

Power Output

ALL MODELS: Power Output Per Channel

300 watts RMS per channel; 20 Hz – 20 kHz; THD < 0.1%; into 8 Ohms
550 watts RMS per channel; 20 Hz – 20 kHz; THD < 0.2%; into 4 Ohms
800 watts RMS per channel; 20 Hz – 20 kHz; THD < 0.5%; into 2 Ohms

ALL MODELS: FTC Rated Power; 2 Channels Driven; 20 Hz – 20 kHz; THD <0.1%

300 watts RMS per channel; THD < 0.1%; into 8 Ohms (120 VAC line).
490 watts RMS per channel; THD < 0.1%; into 4 Ohms (120 VAC line).

XPA Gen3 Power Per Channel: All Channels Driven; THD <0.1% ; into 8 ohms

Two:300 watts RMS per channel
Three:275 watts RMS per channel
Four:260 watts RMS per channel
Five:250 watts RMS per channel
Six:225 watts RMS per channel
Seven:200 watts RMS per channel

 Power Bandwidth (at rated power; 8 Ohm load)

20 Hz to 20 kHz (+ / – 0.1 dB).

Broad Band Frequency Response

5 Hz to 80 kHz (+ 0 / – 0.15 dB).

THD + noise

< 0.005%; at 100 watts RMS; 1 kHz; 8 Ohms

Signal to Noise Ratio (8 Ohm load)

> 115 dB; ref FTC rated power; unbalanced input (A-weighted).
> 86 dB; ref 1 watt; unbalanced input (A-weighted).

Minimum Recommended Load Impedance

4 Ohms; which equals one 4 Ohm load or two paralleled 8 Ohm loads.

Damping Factor (8 Ohm load)

> 500.

Speaker Output Connections

Audiophile grade, gold plated, 5-way binding posts.

Power Supply

High efficiency, audiophile grade, Switch Mode Power Supply (SMPS).

Input Sensitivity (for rated power; 8Ohm load)

1.5 V.

Gain

29 dB.

Input Connections

Unbalanced (RCA); balanced (XLR); one each per channel, independently selectable.

Input Impedance

33 kohms (balanced).
23.5 kohms (unbalanced).

Trigger

Trigger Input: 5 – 12 V (AC or DC); <10 mA input current required.
Trigger Output: 12 VDC; can drive any load up to 120 mA.

Power Requirements

Between 100 VAC and 250 VAC @ 50 / 60 Hz (automatically detected).

Protection

The XPA Gen3 is protected against excessive operating temperature, shorted speaker connections, ground faults, and other common fault conditions.

Informations complémentaires

Poids50 lbs
Marque

Nombre de canaux

2, 3, 4, 5, 6, 7, 9, 11